Remote-processing RPC-30 Manual de usuario Pagina 7
- Pagina / 38
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 2 SETUP AND OPERATION
RPC-30 Page 5
FIRST TIME OPERATION
Become familiar with the locations of the connectors
before getting started. See Figure 2-1.
RPC -30 jumpe rs have been set at the factory to operate
the system immediately. For first time operation, do not
install any connectors or parts unless specified below.
Jumpers should be kept in default positions. See
Technical Information.
1. The RPC -30 needs + 5 ±0.25 volts at 100 ma. Any
well regulated supply that supplies this will work.
Be careful when using "switching" power supplies.
Some of these supplies do not regulate proper ly
unless they are adequately loaded. Don' t forget that
power requir ements w ill increase w hen opto
modules are installed. The G5 series requires about
130 - 150 ma per module.
Make sure pow er is off. Connect the power supply
to the appropriately marked terminals on the RPC-
30.
2. You can use either a PC or CR T term inal to
program the RPC-30. Connect one end of the VTC-
9F connector to then 10 pin COM 1 port on the
RPC-30. Refer to Figure 2-1 for connector
location.
Using a PC
Connect the VTC-9F serial cable to the PC's COM1
or COM 2 port. Y ou may need a 9 pin male to 25
pin female adapter. T he VT C-9F is designed to
plug directly into the 9 pin serial port connector on a
PC.
Start up your serial communication program (PC
SmartLINK or other). Set communication
parameters to 19. 2K baud, 8 data bits, no parity, 1
stop.
Using a Terminal
Follow your terminal instructions to set the baud
rate to 19.2K baud, 8 data bits, no parity, and 1
stop. You may need a 9 pin male to 25 pin male
adapter to connect the VTC-9F.
3. Turn on your power supply. On pow er up a
copyright message is printed.
CAMBASIC (tm) (c) 1985-93
Octagon Systems Corporation
Remote Processing Corporation
All rights reserved
Bytes Free - 27434
If a nonsense message appears, your terminal or PC
may not be set to the appropriate communication
parameters. If the system still does not respond,
refer to "TROU BLESH OOT ING" later in this
chapter.
4. The system is now in the " imme diate mod e" and is
ready for you to start programming. T ype the
following program (in upper or lower case):
10 FOR X = 0 TO 2
20 PRINT " Hello ";
30 NEXT
40 PRINT
Now type RUN
The system will display:
Hello Hello Hello
UPLOADING AND DOWNLOADING
PROGRAMS
Downloading program s means transferring them from
your PC (or terminal) to RAM on the RPC-30.
Uploading means transferring programs from RAM back
to the PC. This section explains how to do both of these
procedures using PC SmartLink. Generalized
instructions for other terminal programs are given at the
end of this section.
Uploading programs
In the previous section, you wrote a test program. To
upload that program to a PC and save it to disk:
1. Press the < F1> key. A window with the main
menu will appear.
2. Press the letter U (upper or lower case). Your
program will begin to transfer from RAM to the
PC. When m enu appears.
3. To save a program to disk, type the letter S. You
are prompted for a file name. Enter the file name
you want the program saved under.
- TRADEMARKS 1
- NOTICE TO USER 1
- TABLE OF CONTENTS 2
- CHAPTER 1 OVERVIEW 3
- OVERVIEW CHAPTER 1 4
- SETUP AND OPERATION CHAPTER 2 10
- CHAPTER 2 SETUP AND OPERATION 11
- SAVING PROGRAMS CHAPTER 3 12
- CHAPTER 3 SAVING PROGRAMS 13
- SERIAL PORTS CHAPTER 4 14
- CHAPTER 4 SERIAL PORTS 15
- RAM MEMORY CHAPTER 5 18
- CHAPTER 5 RAM MEMORY 19
- INTRODUCTION 22
- WARNING: 22
- ON-CARD OPTO RACK 22
- DIGITAL I/O PORT 23
- Page 24 RPC-30 26
- COMMANDS 27
- CALENDAR/CLOCK CHAPTER 7 28
- CHAPTER 8 DISPLAY PORT 29
- DISPLAY PORT CHAPTER 8 30
- CHAPTER 9 KEYPAD PORT 31
- KEYPAD PORT CHAPTER 9 32
- CHAPTER 10 SPEAKER 33
- WATCHDOG TIMER CHAPTER 11 34
- CHAPTER 12 USER JUMPERS 35
- SERIAL EEPROM CHAPTER 13 36
- TECHNICAL INFORMATION 37
Relacionado con productos y manuales para Ordenadores Remote-processing RPC-30
JVC AV-14JT5EU manuals
Owner’s manuals and user’s guides for LCD TVs JVC AV-14JT5EU.
We providing 1 pdf manuals JVC AV-14JT5EU for download free by document types: User Manual
Table of contents
CONTENTS
3
Auto setup
11
INSTALLATION
12
Manual tuneu
13
Fine tune
13
Manual tune
16
C50 Pr01
16
DAILY USE
18
MENU MENU
25
TELETEXT
26
More products and manuals for LCD TVs JVC
| Models | Document Type |
|---|---|
| LT-17E31 BUG |
User Manual
JVC LT-17E31 BUG User's Manual,
33 pages
|
| DynaPix LT-26DR7SJ |
User Manual
JVC DynaPix LT-26DR7SJ User's Manual,
26 pages
|
| HD-56ZR7U |
User Manual
JVC HD-56ZR7U User's Manual,
26 pages
|
| LT-32F70BC |
User Manual
JVC LT-32F70BC User's Manual,
32 pages
|
| GGT0220-001A-H |
User Manual
JVC GGT0220-001A-H User's Manual,
20 pages
|
| PD-35S50J |
User Manual
JVC PD-35S50J User's Manual,
57 pages
|
| PD-35B50BJ |
User Manual
JVC PD-35B50BJ User's Manual,
59 pages
|
| DR-MX1S |
User Manual
JVC DR-MX1S User's Manual,
100 pages
|
| AV-28T77SK |
User Manual
JVC AV-28T77SK User's Manual,
40 pages
|
| AV 30W476 |
User Manual
JVC AV 30W476 User's Manual,
52 pages
|
| LT-32EX177 |
User Manual
JVC LT-32EX177 User's Manual,
22 pages
|
| LT-42EM59 |
User Manual
JVC LT-42EM59 User's Manual,
52 pages
|
| AV-21QS5SP |
User Manual
JVC AV-21QS5SP User's Manual,
15 pages
|
| HD-Z56RX5 |
User Manual
JVC HD-Z56RX5 User's Manual,
34 pages
|
| AV28S2EK |
User Manual
JVC AV28S2EK User's Manual,
35 pages
|
| LT-15B60SW |
User Manual
JVC LT-15B60SW User's Manual,
29 pages
|
| GGT0362-001A-H |
User Manual
JVC GGT0362-001A-H User's Manual,
1 pages
|
| GD-42X1 |
User Manual
JVC GD-42X1 User's Manual,
144 pages
|
| AV-27GFH |
User Manual
JVC AV-27GFH User's Manual,
80 pages
|
| LCT1445-001A |
User Manual
JVC LCT1445-001A User's Manual,
44 pages
|
© 2020, manymanuals.es. Todos los derechos reservados | 0.017 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales